| To display IMEI
type *06#
1. Software Version : *#9999# and *#0837#
(instructions)
2. Serial Port Info : *#0001#
3. Batt./Temp. Meter : *#0228#
4. Sim Card Info : *#0778#
5. SIM capacity display: *#0746#
6. Memory error : *#0377# Use side keys to
select values. Cancel and ok.
7. Error Message : *#0785#. If ok is pressed
the phone will reset and
register this on the memory error.
8. Alarm Tone Adjust : *#0289#
9. Date/Time Log : *#0786# Last up and down.
10. Memory Info : *#0246#
11. LCD Contrast : *#0523# Only with version
G60RL01W.
12. Network Monitor : *#0324#
13. Memory Usage : *#0636#
14. Trace Watcdog : *#0427#
15. Buzzer adjust : *#0289#
16. Phone Parameter : *#0862# Normal, Earphone or
carkit can be
selected.
17. Activate light & Vibra : *#7698# Flash the
screenligth during 10 seconds,
the activation of vibration system.
18. Activate smiley. : *#9125# Activates the
smiley when charging.
Unidentified Code:
*#0872# Diag? Parameter can be changed
with sidekeys.
*#0544#: Jig detect ?
*#0364# Watchdog ?
NB! Since version G60RL23M , it seem that
only *#06# , *#0001#
e *#9999#, works.
Pin-Out 1- GND 2- RS232 TXD 3- RS232 RXD
4- RS232 RTS 5- MAX 4.2 IN ??? 6- GND 7- GND 8- SPK - OUT 9- SPK +
OUT 10- SCL I2C comm proprietary bus 11- SDA I2C comm proprietary
bus 12- RS232 CTS 13- VCC 5V OUT 14- DC 9V IN 15- DC 9V IN 16- MIC
+ IN 17- MIC - IN 18- +3.6V IN battery 19- GND 20- Antenna 21-
Antenna 22- GND 23- GND 24- n.c. 25- Temperature sensor IN 26-
+3.6V IN battery 27- GND 28- GND
SP-unlock SGH-600
*2767*3855# -> Full EEPROM Reset (
THIS CODE REMOVES SP-LOCK!! )
*2767*2878# -> Custom EEPROM Reset
These codes has been tested with version FLD_2C6 G60SB03X of
Samsung SGH-600
Samsung SGH-600 / SGH-2100 Mobile Home
*#9998*228# -> Battery status
(capacity, voltage, temperature)
*#9998*246# -> Program status
*#9998*289# -> Change Alarm Buzzer Frequency
*#9998*324# -> Debug screens
*#9998*364# -> Watchdog
*#9998*377# -> EEPROM Error Stack - Use side keys to select
values. Cancel and ok.
*#9998*427# -> Trace Watchdog
*#9998*523# -> Change LCD contrast - Only with version G60RL01W
*#9998*544# -> Jig detect
*#9998*636# -> Memory status
*#9998*746# -> SIM File Size
*#9998*778# -> SIM Service Table
*#9998*785# -> RTK (Run Time Kernel) errors - if ok then phn is
reset, info is put in memory error. *#9998*786# -> Run, Last
UP, Last DOWN
*#9998*837# -> Software Version
*#9998*842# -> Test Vibrator - Flash the screenligth during 10
seconds and vibration activated.
*#9998*862# -> Vocoder Reg - Normal, Earphone or carkit can be
selected
*#9998*872# -> Diag
*#9998*947# -> Reset On Fatal Error
*#9998*999# -> Last/Chk
*#9998*9266# -> Yann debug screen
(=Debug Screens?)
*#9998*9999# -> Software version
If the up Codes doesn't work, you should
change *#9998* to *#0. i.e. *#9998*523# change to *#0523#. An
other thing that will help is to remove your simcard.
*0001*s*f*t# -> Changes serial
parameters (s=?, f=0,1, t=0,1) (incomplete)
*0002*?# -> unknown
*0003*?# -> unknown
SP-unlock SGH-600 and SGH 2100
*2767*3855# -> Full EEPROM Reset (
THIS CODE REMOVES SP-LOCK!! )
But also changes IMEI to 447967-89-400044-0, To restore your old
IMEI use the IMEI program found on the software page.
*2767*2878# -> Custom EEEPROM Reset
|
Ostali testovi